Call (208) 546-5906

Home / Problems

Tankless Water Heater Error Codes Nampa ID: What the Display Means and What to Do First

Tankless water heater error codes in Nampa tell you why the hot water stopped. The display shows a number or a letter and a number. That code points at the part that is failing. This page tells you what each code family means, what to check first, and when to call a pro.

Technician pressing a button on a wall-hung tankless water heater with a warning light in a Nampa home

Tankless water heater error codes in Nampa tell you why the hot water stopped. The display shows a number or a letter and a number. That code points at the part that is failing. This page tells you what each code family means, what to check first, and when to call a pro.

Nampa HeatPros repairs tankless water heaters in Nampa, Idaho. We work on Rheem, Bradford White, A.O. Smith, Navien, Rinnai, Noritz, and State units.

What to Do First When a Code Shows Up

Before you look up the code, check five things. Most codes come from one of these.

Check the gas. If the gas is off at the meter or at the unit, the heater cannot fire. Check that the gas valve to the unit is open. If other gas appliances work, the gas supply is fine.
Check the water. A tankless unit needs a minimum flow to fire. Open a hot tap fully and see if the flow is strong. A clogged inlet filter can stop the unit from firing.
Check the power. Make sure the unit is plugged in and the breaker has not tripped. A tankless unit needs power to run its controls, even a gas unit.
Check the vent. Look outside at the vent terminal. Snow, ice, leaves, or a bird nest can block it. Nampa has 132 freezing nights a year, according to NOAA, 1991 to 2020.
Check the display. Write down the exact code before you reset anything. The code disappears after a reset.

No Ignition Codes: Rinnai 11, Navien E003, Takagi 111

What it means. The igniter sparked and no flame followed. The unit shuts down for safety and shows the code. Common causes are gas supply off or low gas pressure, a failed igniter, or a gas valve stuck shut.
What to check first. Check the gas valve and other gas appliances. If the gas is fine and the code stays, the igniter or gas valve needs testing. Do not open the gas side yourself.
How much it costs. A tankless repair costs $300 to $1,300 nationally, according to HomeGuide, 2026. A gas control valve costs $150 to $550 nationally.

Flame Loss Codes: Rinnai 12, Navien E012, Takagi 121

What it means. The burner lit, then the flame went out while the unit was running. The flame rod is the part that proves the flame is lit. If it cannot sense the flame, the unit shuts down and shows the code. Common causes are a dirty flame rod, low gas pressure, a venting fault, or scale in the heat exchanger.
What to check first. Check the vent outside and the gas supply. If the code comes back after one reset, the flame rod or gas valve needs testing.

Overheat Codes: Rinnai 14, Navien E016 and the 400 Series, Including E407

This is the most common code family in Nampa, and hard water is the reason.

What it means. The water inside the unit got too hot, so the unit shut down. Scale is the usual cause. Nampa water runs up to 7.08 grains per gallon, according to the City of Nampa 2024 water quality report. Scale coats the heat exchanger, traps heat, and drives the temperature up. Low water flow makes it worse.
What to check first. Check the water flow at a hot tap. If the flow is weak, the inlet filter may be clogged. If the flow is strong and the code stays, the unit needs a descale.
How much it costs. A tankless descale costs $75 to $300 nationally, according to HomeGuide, 2026. A heat exchanger replacement costs $600 to $1,300.

Venting and Condensate Codes: Rinnai 10, Rheem 29

A venting code means the unit cannot breathe out. A condensate code means the unit cannot drain.

Rinnai 10, venting. The vent carries exhaust gas outside. If the vent is blocked, the unit shuts down. Check the vent terminal outside for snow, ice, leaves, or a nest. In Nampa winters, ice on the vent is a common cause.
Rheem 29, condensate. A condensing tankless unit makes water as it runs, and that water drains out through a condensate line. If the line is blocked or frozen, the unit shuts down and shows the code. Check the condensate line for a blockage or ice. Do not bypass it.
What to check first. Clear a blockage you can see at the vent terminal or the condensate line. If the code stays, the vent or the condensate trap needs testing.

The Reset Rule

The reset rule is simple. Reset once. Twice at most. If the code comes back after two resets, stop and call us.

Resetting again and again does not fix the fault. It hides it, and it can make the damage worse. An overheat code that keeps getting reset can cook the heat exchanger. A flame loss code that keeps getting reset can wear out the igniter.

To reset, turn the unit off at the control panel, wait a minute, and turn it back on. Check your model manual for the exact steps. Codes vary by model, so the manual for your exact unit is the final word.

When to Call a Pro

Gas smell. If you smell gas, do not reset the unit. Leave the house and call the gas company first, then call us.
Code keeps coming back. A code that returns after two resets means a part has failed. The unit needs testing, not more resets.
No hot water in winter. Nampa has 132 freezing nights a year, according to NOAA, 1991 to 2020, with a January average low of 23 degrees. A tankless unit with no hot water in January is an emergency.
Leaking unit. Water on the floor under a tankless unit means a failed seal, a cracked heat exchanger, or a leaking connection. Shut off the water to the unit and call us.

Why Nampa Tankless Units Show Codes

Hard water lays scale in the heat exchanger. Scale drives overheat codes, cuts flow, and trips flame loss codes. A yearly descale keeps the heat exchanger clean. A descale costs $75 to $300 nationally, according to HomeGuide, 2026.

Winter freezes vents and condensate lines. Ice on the vent trips venting codes. A frozen condensate line trips condensate codes.

A tankless unit lasts 15 to 20 years, according to the U.S. Department of Energy, and it is 24 to 34 percent more efficient than a tank for homes using 41 gallons of hot water a day or less.

Tankless Water Heater Error Codes Across Nampa

We drive to homes all over Nampa, and to Meridian, Caldwell, Kuna, Middleton, Star, and Boise. In Nampa, that means downtown, North Nampa, South Nampa around Lake Lowell, East Nampa along Ustick Road, the NNU area, West Nampa near Garrity Boulevard, and the Karcher and Greenhurst area.

Newer homes in Copper River Basin, Karcher Estates, Sundance, and the Ten Mile corridor often have tankless units, and overheat codes there usually mean scale. Older homes near downtown, around Nampa High School, often have older tankless units, and no ignition codes there usually mean a worn igniter.

Tankless Error Codes in Nampa: FAQs

What does error code 11 mean on a Rinnai tankless water heater?

It means no ignition. The unit tried to light and failed. Check the gas valve and the gas supply first.

What does E003 mean on a Navien tankless water heater?

It means no ignition, the same fault as Rinnai 11. Check the gas supply, then call us if the code comes back after one reset.

What does E016 mean on a Navien tankless water heater?

It means overheat. The water inside the unit got too hot, usually from scale in the heat exchanger. Check the water flow at a hot tap. If the flow is weak, the inlet filter may be clogged.

Can I reset my tankless water heater myself?

Yes. Reset once, twice at most. Turn the unit off at the control panel, wait a minute, and turn it back on. If the code comes back, stop resetting and call us.

How much does it cost to fix a tankless error code?

Nationally, a tankless repair costs $300 to $1,300, according to HomeGuide, 2026. A descale costs $75 to $300.

Book Your Tankless Water Heater Repair in Nampa Today

A code on the display is the unit telling you what is wrong. Tell us the code, the brand, and what you checked first. We will diagnose it, quote it in writing, and fix it the same day where we can. That is how tankless water heater error codes Nampa ID should work.

Our tankless repair page has the full fix for each code family.


Our Service Area

We serve Nampa and the towns around it. Pick your area to see water heater repair there.

Water Heater Repair in Caldwell, IDWater heater service in Caldwell, IDWater Heater Repair in Star, IDWater heater service in Star, IDWater Heater Repair in Middleton, IDWater heater service in Middleton, IDWater Heater Repair in Meridian, IDWater heater service in Meridian, IDWater Heater Repair in Kuna, IDWater heater service in Kuna, IDWater Heater Repair in Huston, IDWater heater service in Huston, IDWater Heater Repair in Greenleaf, IDWater heater service in Greenleaf, IDWater Heater Repair in Melba, IDWater heater service in Melba, IDWater Heater Repair in Notus, IDWater heater service in Notus, IDWater Heater Repair in Downtown Nampa, IDWater heater service in Downtown Nampa, IDWater Heater Repair in North Nampa, IDWater heater service in North Nampa, IDWater Heater Repair in South Nampa, ID (Midland / Lake Lowell)Water heater service in South Nampa, ID (Midland / Lake Lowell)Water Heater Repair in East Nampa, ID (Ustick / Ten Mile)Water heater service in East Nampa, ID (Ustick / Ten Mile)Water Heater Repair in West Nampa (Garrity / Ford Idaho Center), IDWater heater service in West Nampa (Garrity / Ford Idaho Center), IDWater Heater Repair near Northwest Nazarene University, Nampa, IDWater heater service near Northwest Nazarene University, Nampa, IDWater Heater Repair in the Karcher / Greenhurst Area, Nampa, IDWater heater service in the Karcher / Greenhurst Area, Nampa, IDWater Heater Repair in Lake Lowell / Deer Flat, Nampa, IDWater heater service in Lake Lowell / Deer Flat, Nampa, ID

No hot water in Nampa?

Same-day emergency water heater repair, upfront pricing, local specialists.

Call Now (208) 546-5906
(208) 546-5906